Takata Midi Instruction Manual download pdf (Page 23)

4. USE IN THE VEHICLE

WARNING!

[MIDI_009] Never use the TAKATA ISOFIX BASE

on its own, or without properly securing the TAKATA

MIDI. Failure to observe this notice may seriously risk

your child’s safety, and the safety of other passengers.

NOTE!

Long-term use of the TAKATA ISOFIX BASE and

TAKATA MIDI may result in wear and tear of the

vehicle seat.

Securing the TAKATA ISOFIX BASE

Step 1 – Fold out the support leg

Fold out the support leg as explained in Section 3 –

Basic instructions (Adjusting the support leg), and

ensure that it is properly locked in place.

NOTE!

Check the support leg is locked in place by lightly

shaking it with your hand.

Step 2 – Place on the vehicle seat

[MIDI_027] Place the TAKATA ISOFIX BASE on the

seat of the vehicle. Ensure that:

• The ISOFIX connectors are pointing to the back of

the car seat.

• The support leg is pointing to the vehicle ﬂ oor.

Step 3 – Pull out the ISOFIX connectors

[MIDI_023] Press in the button on the inner side of

each rear connection arm as far as possible, and fully

extend the connectors. Follow the instruction in

Section 3 – Basic instructions (Adjusting the ISOFIX

connectors).

NOTE!

The connectors have been fully extended when no

ﬁ gure is displayed on the top of them.

Step 4 – Connect the ISOFIX system

[MIDI_028] Point the open ISOFIX connectors on the

TAKATA ISOFIX BASE towards the ISOFIX points of

the vehicle. Slide the connectors into the vehicleʼs

ISOFIX points, until each one clicks into place, and

the green markings are visible on the release sliders.

NOTE!

[MIDI_029] If the vehicleʼs ISOFIX points are difﬁ cult

to reach, use the feeder supplied to guide them out.

This makes connecting the system much easier, and

protects the seat cover.

WARNING!

Ensure that both ISOFIX connectors are fully secured

to the vehicleʼs ISOFIX points. Failure to observe

this notice may seriously risk your child’s safety, and

the safety of other passengers. You can check the

connectors are properly secured to the ISOFIX points,

by lightly shaking the TAKATA ISOFIX BASE.

Step 5 – Fit the base against the back of the vehicle

seat

[MIDI_030] Press the two buttons to adjust the length

of the ISOFIX connectors, and push the TAKATA

ISOFIX BASE until it sits ﬂ ush against the seat back.

WARNING!

[MIDI_031] When ﬁ xing the TAKATA ISOFIX BASE

to the vehicle seat, ensure that both ISOFIX

connectors are set correctly and to the same position.

Check this by lightly shaking the TAKATA ISOFIX

BASE, and check that the ﬁ gures on the top of the

connectors match up (or that both are blank). Failure

to observe this notice may seriously risk your child’s

safety.

Step 6 – Adjust the support leg

[MIDI_032] Set the height of the support leg, following

the instructions in Section 3 – Basic instructions

(Adjusting the support leg), so that its base lies on the

vehicle ﬂ oor.

WARNING!

Ensure that the support leg is locked into position, and

that it lies ﬂ ush against the ﬂ oor. Failure to observe

this notice may seriously risk your child’s safety, and

the safety of other passengers.

NOTE!

Check the support leg is locked in place by gently

pushing and pulling it.

NOTE!

If you notice that the TAKATA ISOFIX BASE can

still be moved around on the vehicle seat, repeat all

the steps in Section 4 – Use in the vehicle (Securing

the TAKATA ISOFIX BASE), until the base is ﬁ rmly

secured to the vehicle seat.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 73 74

Comments to this Manuals

No comments

Takata Midi Instruction Manual Page 23

Comments to this Manuals

Related products and manuals for Car seats Takata Midi