Takata Maxi Instruction Manual download pdf (Page 18)

1414

NOTE!

Hold the base of the seat in position, while pulling the

back up.

Step 2 – Release the angle locking mechanism and

fold up

[MAXI_021] Fold the lower section of the seat back

cover upwards, and push the release slider up.

[MAXI_022] At the same time, use your other hand to

fold the seat back down, until it lies ﬂ at on the base.

Step 3 – Push the seat together into the transport

position

[MAXI_023] Release the seat back locking mechanism

(as in Step 1 “Pull the seat back up to the highest

position”) and press the back down into the base as far

as possible.

NOTE!

To prevent the seat from folding open, the bottom

edges of the side wings can be secured beneath the

front tip of the armrests.

CAUTION!

Always check that the seat back is locked in place, by

lightly pulling it up, without lifting the lever. If you

hear a click, it is ﬁ rmly in position.

Removing the seat back

Step 1 – Pull out the seat back

[MAXI_017] Release the seat back locking mecha-

nism and pull the back up as high as possible (see Step

1 of “Folding out and setting up the back”).

Step 2 – Unfasten the cover

[MAXI_024] Unfasten the two straps on the seat base

cover (one strap on each side), positioned on the outer

sides of the armrests. Pull the ends of the cover up.

Step 3 – Remove the safety bolts

[MAXI_025] Press the heads of the safety bolts

together, and remove these from their sockets.

Step 4 – Separate the back and base of the seat

[MAXI_026] Push the axle of the seat back out of its

holders in the base. The back of the seat can then be

lifted off the base.

Attaching the seat back

To attach the back of the TAKATA MAXI to the base,

follow the instructions given in “Removing the seat

back” in reverse order.

3. BASIC INSTRUCTIONS

CAUTION!

Always place the TAKATA MAXI child car seat on

a ﬂ at, stable surface.

CAUTION!

Be careful that your ﬁ ngers and other body parts do

not get caught in any moving sections of the seat.

Folding out and setting up the back

Step 1 – Release and pull out the back of the seat

[MAXI_017] Locate the lever on the rear of the seat

back, pull it up, and hold it in position. At the same

time, pull the seat back up as far as possible. You can

now release the lever.

Step 2 – Fold out the seat back

[MAXI_018] Open the seat up until the angle between

the back and base is at least 90°, and you hear a click.

Step 3 – Set the height of the back

[MAXI_019] Release the seat back locking mecha-

nism and adapt the height of the seat back to the size

of the child’s body (see Step 1 of this section).

If frequently folding the seat up and open again, the

size indicator will help you ﬁ nd the right height

quickly (there are 11 positions marked from A to L).

WARNING!

Always adapt the height of the seat back to the size of

the child’s body. Ensure that the top of your child’s

head is positioned below the top edge of the headrest.

If the headrest is too low, there is a greater risk of

injury in the case of an accident. At the same time, the

shoulder belt guide should be no more than two ﬁ nger

widths above the child’s shoulder.

CAUTION!

Always check that the seat back is locked in place, by

lightly pushing down on it, without lifting the lever. If

you hear a click, it is ﬁ rmly in position.

Folding the seat back down

Step 1 – Pull the seat back up to the highest position

[MAXI_020] Release the seat back locking mecha-

nism and pull the back up as high as possible (see Step

1 of “Folding out and setting up the back”).

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 53 54

Comments to this Manuals

No comments

Takata Maxi Instruction Manual Page 18

Comments to this Manuals

Related products and manuals for Car seats Takata Maxi